| A. LENGTH : 5.32 Mts. (1'
5.5") |
C. HEIGHT : 2.19 Mts. (7'
2.5") |
E. REAR TRACK : 1.87 Mts.
(6' 2") |
| B. WIDTH : 2.44 Mts. (8'
0") |
D. FRONT WHEEL TRACK :
1.93 Mts.
(6' 3.75") |
F. WHEEL BASE : 2.56 Mts.
(8' 4.75") |
TECHNICAL SPECIFICATION
|
Transmission |
Mechanical |
CAPACITY OF TANK |
|
Front Wheel |
Solid Rubber Tyre
2 Nos. 550 Dia. x 175 mm |
Fuel |
120 L |
Hydraulic
Oil |
45 L |
|
Rear Wheel |
2 Nos. Pneumatic Tyre
Size : 10.00 x 20, 16 ply |
Screed |
The main screed is pivoted at the center point of the
machine to assure a constant flatness of work on uneven
grounds. It consists of 2.44 mtrs. main screed with mechanical extension of
suitable size to work up to 4.0 mtrs. The screed plate is 450 mm wide, 12 mm
thickness. |
|
Max. Opt. Wt. |
8500 Kgs. Approx. |
Hopper
Capacity |
4.25 CM |
STANDARD ACCESSORIES
Canvas Canopy
Working Lights
Traveling Lights
Tool kit with Jack |
|
Auger Screw |
Dia 250 mm. (10") Ni-Hard material |
|
Speed |
Traveling : 16 Kmph (max)
Working : 1.27 to 24 Mts/min.
(4.17 to 78.72 FPM) |
PRIME MOVER Kirloskar make water-cooled electric start Diesel Engine
Model 4R-1040 ( 60 hp @ 2000 rpm) or equivalent
TRANSMISSION Mechanical transmission. Eight speed reduction gearbox with
differential and differential lock arrangement. All the gears are in oil bath.
SCREED The main screed is pivoted at the center point of the machine to
assure a constant flatness of work on uneven grounds. It consists of 2.44 mtrs.
main screed with mechanical extension of suitable size to work up to 4.0 mtrs.
and hydraulic vibration.
BRAKES The brakes consist of hydraulic caliper and brake booster, which
is controlled by pedal from operator's seat. The safety brakes are acting on the
speed shaft, which are coupled to the drive wheels.
THRUST ROLLER Two thrust rollers are fixed on front beam fitted on front
part of the machine.
OPERATOR'S SEAT Operator's seat is fitted on the left side of the
machine. The seat is adjustable. All panels and levers are within the easy reach
of the oprator.
HOPPER AND FEEDING SYSTEMS The movement of two hoppers is obtained by
means of hydraulic cylinder. Two conveyor chains one on each side is
independently controlled and made of harden steel. Material conveyed on both
side is sprayed by two auger, both auger, both independently controlled by
levers provided near the operator's seat.
ELECTRICAL SYSTEM 12 V battery is provided for working and traveling of
machine.
SALIENT FEATURES
• Single level control for speed gearing is
provided which prevent dual engagement and braking of gears
• All operating
levers including panel switch board are handy and within easy reach
• All gears
and shafts of gear box are made from alloy steel and are hardened and ground for
efficient working
• Screed is vibrated with hydraulic motor for compacting the
laid layer
• Gas burners are provided for heating the main screed
• All jacks
are having one kind of seal kit ( Piston seal and rod of PU material )
(
NOTE : SPECIFICATION/DESCRIPTION ARE INDICATIVE AND SUBJECT TO CHANGE WITHOUT NOTICE
DUE TO MODIFICATION ALTERATION OR CUSTOM ENGINEERING )
|
